Peanup Docs Product 简体中文
Menu
On this page 01Quick check
PEANUP / SETUP & HELP01

Keep the frame.
Find the step that stopped.

One Peanup update moves through preparation, discovery, connection, transfer and refresh. Do not restart everything blindly; identify the current stage and continue from there.

POWERStart with available charge NEARBYStay close while sending KEEPRetain the prepared frame RETRYResume from the failed stage

Crowdfunding preview path · final prompts depend on the released app and hardware

02 / ONE-MINUTE CHECK

Four small checks
before one clean retry.

  1. 01 / POWERAdd power

    Place Peanup flat at the center of a compatible Qi charger.

  2. 02 / PERMISSIONCheck Bluetooth access

    Enable system Bluetooth and allow the Peanup app to use it.

  3. 03 / DISTANCEKeep both devices nearby

    Leave the phone and Peanup close and steady during discovery and transfer.

  4. 04 / STAGENote where it stopped

    Distinguish discovery, connection, transfer and refresh instead of repeating blindly.

Where did it stop?

Choose the state you can see now. This gives one next step without discarding the prepared frame.

Do this now Make the device visible first

Confirm available power, system Bluetooth and app permission, then end the old scan and start one clean scan.

Do not choose the photo again yetKeep the cropped and rendered frame after a connection failure, then resume from the connection stage.

03 / DEVICE DISCOVERY

No device in the list?
Check discovery conditions first.

What you seeDo this firstAvoid this
The scan list is emptyConfirm power, the Bluetooth switch and app permission, then start one new scan.Do not tap scan rapidly or open several transfer screens at once.
Several devices appearUse the device name and recent-device record; move other units away temporarily.Do not identify a device only by its list position.
The device appears, then vanishesStay close, confirm another phone is not connected, then discover again.Do not start while moving the device or while charging placement is unstable.
Bluetooth permission is deniedRestore permission in system settings, return to the app and scan again.Do not report denied permission as damaged hardware.
Review Bluetooth conditions
04 / TRANSFER

When sending stops,
show more than a progress bar.

An update has more states than “success” and “failed.” Progress distinguishes discovery, connection, transfer, acknowledgement and panel refresh.

If transfer is interrupted, retain the completed frame and known progress, move closer and retry. Cropping and rendering need to run again only when you choose a different source.

Send to one Peanup at a time. Backgrounding the app, locking the phone, leaving Bluetooth range or losing permission can interrupt the current connection.

StageVisible statusNext action
DiscoveryLooking for nearby devicesStay close and confirm permission and power.
ConnectionEstablishing a nearby connectionDo not switch devices or leave the flow.
TransferExplicit block progress and a cancel stateRetain the frame and retry from transfer after interruption.
RefreshTransfer complete; the panel is updatingWait without moving the device or sending again.
CompleteThe new frame is written and heldThe connection may return to idle.
05 / E-PAPER REFRESH

You can see the refresh.
Then the paper becomes quiet.

NORMAL

Brief flashing and color changes

E-paper visibly moves pigments into place. A transition during this drive sequence does not by itself mean the image is damaged.

WAIT

Use the app completion state

Transfer complete is not refresh complete. Wait for explicit confirmation before moving the device or sending the next frame.

KEEP

The image remains offline

After a complete write, e-paper does not need an active Bluetooth connection or a backlight to keep the content.

STOP & CHECK

If the panel remains between frames, refreshes repeatedly or the app reports an error, stop sending again, record the stage and prepare the details in “Contact support.”

06 / QI CHARGING

No response on the charger?
Realign from the center.

ALIGN

Start from the center

Remove metal plates, thick cases and debris, then place Peanup flat at the center of a compatible Qi charger.

PAUSE

Allow a moment for detection

Leave it steady for recognition rather than sliding it continuously across the charging area.

HEAT

Stop on unusual heat

Stop using it if there is moisture, odor, unusual heat or visible charger damage, then contact support.

Qi, the no-exposed-connector enclosure and final charging feedback are crowdfunding targets. Input power, charge time, temperature rise and indicators will be published after production validation.

07 / CUID NFC

Enrollment can fail
without a hardware fault.

Confirm system compatibility, then obtain administrator approval

Peanup may act as an access card only when the reader supports CUID, the administrator permits enrollment and local rules allow it. Reader models, encryption and property policy all affect the result.

Read the complete NFC conditions
08 / USEFUL REPORT

Share the useful context.
Find the problem faster.

DEVICE

Device and system

Phone model, iOS or iPadOS version, Peanup app version and the device name.

STAGE

The step that stopped

Discovery, connection, transfer, panel refresh, Qi charging or NFC enrollment.

TIME

Time and frequency

Approximate time, whether it happens every time and what changed after moving closer or adding power.

PRIVACY

Private originals are not required

Prefer a status screenshot or exact error text. Do not email personal photos or access-card details unless specifically needed.

CONTACT Still stopped?
Write directly to us.

Contact i@caiths.com with the four groups above. We will identify the stage first, then decide whether detailed logs are needed.

09 / FAQ

The most common cases,
answered first.

01Why does Peanup not appear in the device list?

Confirm that the device has power, Bluetooth is enabled and the Peanup app has Bluetooth permission. Keep both devices close, end the current scan and start one clean scan rather than tapping connect repeatedly.

02Will an interrupted transfer erase the existing image?

No. E-paper keeps the last fully written frame. The app should also retain the newly prepared frame and the failed stage so you can retry without choosing the photo again.

03Is flashing, color change or a brief old frame normal during refresh?

E-paper uses a visible drive sequence rather than video-style redraw. Wait until the app explicitly reports completion before moving the device or sending again. Final behavior depends on production hardware.

04What should I do when a Qi charger does not respond?

Remove cases, metal plates and debris, then place Peanup flat at the center of a compatible Qi charger. Stop immediately if there is unusual heat, moisture or damage to the charger.

05Why can CUID NFC enrollment fail?

It can work only when the access system supports CUID, the administrator allows enrollment and local rules permit it. Peanup cannot make an incompatible reader work or bypass authorization.